Search Results

Reactivity controlled compression ignition through in-cylinder blending gasoline and diesel to a desired reactivity has previously been shown to give low emission levels and a clear simultaneous efficiency advantage. To determine the possible viability of the concept for on-road application, the control space of injection parameters with respect to combustion phasing is presented. Four injection strategies have been investigated, and for each the respective combustion phasing response is presented. Combustion efficiency is shown to be greatly affected by both the injection-timing and injection-strategy. All injection strategies are shown to break with the common soot-NOx trade-off, with both smoke and NOx emissions being near or even below upcoming legislated levels. Lastly, pressure rise rates are comparable with conventional combustion regimes with the same phasing. The pressure rise rates are effectively suppressed by the high dilution rates used.

The concept of Partially Premixed Combustion is known for reduced hazardous emissions and improved efficiency. Since a low-reactive fuel is required to extend the ignition delay at elevated loads, controllability and stability issues occur at the low-load end. In this investigation seven fuel blends are used, all having a Research Octane Number of around 70 and a distinct composition or boiling range. Four of them could be regarded as ‘viable refinery fuels’ since they are based on current refinery feedstocks. The latter three are based on primary reference fuels, being PRF70 and blends with ethanol and toluene respectively. Previous experiments revealed significant ignition differences, which asked for further understanding with an extended set of measurements. Experiments are conducted on a heavy duty diesel engine modified for single cylinder operation. In this investigation, emphasis is put on idling (600 rpm) and low load conditions.

This paper focusses on the application of bioalcohols (ethanol and butanol) derived from seaweed in Heavy-Duty (HD) Compression Ignition (CI) combustion engines. Seaweed-based fuels do not claim land and are not in competition with the food chain. Currently, the application of high octane bioalcohols is limited to Spark Ignition (SI) engines. The Reactivity Controlled Compression Ignition (RCCI) combustion concept allows the use of these low carbon fuels in CI engines which have higher efficiencies associated with them than SI engines. This contributes to the reduction of tailpipe CO2 emissions as required by (future) legislation and reducing fuel consumption, i.e. Total-Cost-of-Ownership (TCO). Furthermore, it opens the HD transport market for these low carbon bioalcohol fuels from a novel sustainable biomass source. In this paper, both the production of seaweed-based fuels and the application of these fuels in CI engines is discussed.

Partially Premixed Combustion has shown the potential of high efficiency, emissions of nitrogen oxides (NOx) and soot below future emissions regulations, and acceptable acoustic noise. Low-octane-number gasoline fuels were shown to be most suitable for this concept, with the reactivity determining the possible load range. Other researchers have used several refinery streams, which might be produced by a refinery if they were required to do so without additional investment. Some of refinery streams are, however, not expected to be commercially available on the short term. For the present investigation, n-butanol (BuOH) has been selected as a blend component in diesel, and is used from 50 - 100%. The blends then have a reactivity range similar to the refinery streams, so single-cylinder engine tests for their emission and efficiency performance can also be used to determine their applicable load range.

Gasoline-ethanol-methanol (GEM) blends, with constant stoichiometric air-to-fuel ratio (iso-stoichiometric blending rule) and equivalent to binary gasoline-ethanol blends (E2, E5, E10 and E15 in % vol.), were defined to investigate the effect of methanol and combined mixtures of ethanol and methanol when blended with three FACE (Fuels for Advanced Combustion Engines) Gasolines, I, J and A corresponding to RON 70.2, 73.8 and 83.9, respectively, and their corresponding Primary Reference Fuels (PRFs). A Cooperative Fuel Research (CFR) engine was used under Spark Ignition and Homogeneous Charge Compression Ignited modes. An ignition quality tester was utilized in the Compression Ignition mode. One of the promising properties of GEM blends, which are derived using the iso-stoichiometric blending rule, is that they maintain a constant octane number, which has led to the introduction of methanol as a drop-in fuel to supplement bio-derived ethanol.

In-cylinder visualization, combustion stratification, and engine-out particulate matter (PM) emissions were investigated in an optical engine fueled with Haltermann straight-run naphtha fuel and corresponding surrogate fuel. The combustion mode was transited from homogeneous charge compression ignition (HCCI) to conventional compression ignition (CI) via partially premixed combustion (PPC). Single injection strategy with the change of start of injection (SOI) from early to late injections was employed. The high-speed color camera was used to capture the in-cylinder combustion images. The combustion stratification was analyzed based on the natural luminosity of the combustion images. The regulated emission of unburned hydrocarbon (UHC), carbon monoxide (CO) and nitrogen oxides (NOX) were measured to evaluate the combustion efficiency together with the in-cylinder rate of heat release.

A Gasoline Compression Ignition combustion strategy was developed and showed its capabilities in the heavy duty single cylinder test-cell, resulting in indicated efficiencies up to 50% and low engine out emissions applying to EU VI and US 10 legislations while the soot remained at a controllable 1.5 FSN. For this concept a single-cylinder CI-engine was used running at a lambda of ∼1.6 and EGR levels of ∼50% and a modified injection strategy. Part of this strategy was also the use of a gasoline blended with an ignition improver, giving the blend a cetane number in the range of regular diesel; ∼50. In this paper a step is taken towards implementation of this combustion concept into a multi-cylinder light duty standalone CI-engine. A standard CI-engine was modified so that its gas-exchange system could deliver the requested amounts of EGR and lambda.